Paint (9)

View as
  • Out of Stock Quick view
    Add to wishlist

    Amercoat 235 Multi-Purpose Epoxy

    $68.70

    This item cannot be shipped. Local Pickup Only

    • Exceptional corrosion protection in salt and fresh water immersion and corrosive chemical environments
    • Surface tolerant, lowers the cost of surface preparation
    • Excellent adhesion to tight rust
    • Good adhesion to damp surfaces
    • Low temperature cure, cures down to 0°F (-18°C)
    • Fast dry-to-recoat
    • Self-priming
    Low solvent content meets VOC requirements, reduces the chances for film pinholing and solvent entrapment at the substrate-coating interface, often a major cause of coating failure with conventional epoxies and lower solids systems.

    Typical Uses

    Tank Linings and Pipe Coatings
    • Ballast tanks
    • Bilges, wet voids and drainage pipes
    Ships, Offshore and Marine Structures
    • Above and below-water hull areas
    • Decks and superstructures
    • Multi-purpose repair coating
    Fabrication and New Construction
    • Speeds up production, even at low temperatures
    • A single multi-purpose, surface-tolerant coating
    Please note colors on your computer screen may vary from the actual manufacturer's color. To view the most accurate swatch color please contact the manufacturer's website.
    Quick View
  • Out of Stock Quick view
    Add to wishlist

    Amercoat 450H Aliphatic Polyurethane

    $70.56 Quick View
  • Quick view
    Add to wishlist

    CAT 4C-4200: High Gloss Yellow Spray Paint

    $12.25

    This item cannot be shipped. Local Pickup Only

    PlastiKote has you covered for your automotive paint, specialty paint, automotive touch-up and scratch repair needs!
    Quick View
  • Quick view
    Add to wishlist

    Krylon Colormaster Clear Satin

    $8.50

    This item cannot be shipped. Local Pickup Only

    Provides a permanent, protective satin coating that will not yellow with age. Moisture-resistant and smudge-proof. Improves artwork and photo contrast.
    • Permanent, protective satin finish
    • Non-yellowing
    • Moisture-resistant
    • Dries in minutes
    Quick View
  • Out of Stock Quick view
    Add to wishlist

    PPG Dimetcote 302H Green Resin

    $105.60

    This item cannot be shipped. Local Pickup Only

    • Can be topcoated as soon as Dimetcote 302 is solvent free
    • Outstanding resistance to water, weather and abrasion
    • Superior performance on marine hulls, decks and superstructures
    • Resistant to dry spray, mudcracking and topcoat bubbling
    • Easily applied by airless or conventional spray and brush
    Typical Uses (with suitable topcoats) INDUSTRIAL - Structural steel, machinery pipes, and tank exteriors in paper mills, oil refineries, power plants, chemical process and waste treatment plants. MARINE - Decks, hulls and superstructures of ships, barges and workboats. Piers, offshore platforms and related structures.
    Quick View
  • Quick view
    Add to wishlist

    PPG Paint Finish Topcoat

    $68.80 – $81.75

    This item cannot be shipped. Local Pickup Only

    A high performance, low VOC, two-component chemically-cured aliphatic urethane gloss finish. NORTH AMERICA ONLY For use on properly prepared steel, galvanized, aluminium and properly prepared concrete floors. Ideal for use on exterior or interior structural steel, piping, metal buildings, conveyors, pumps, storage tank exteriors, wind turbine towers, motors, machinery, and transportation vehicles. Can also be used in the hard service areas of food processing plants, dairies, schools, restaurants, hospitals, correctional facilities, factories, stadiums, arenas, and amusement parks. Please note colors on your computer screen may vary from the actual manufacturer's color. To view the most accurate swatch color please contact the manufacturer's website.
    Quick View
  • Quick view
    Add to wishlist

    Rust-Oleum High Heat Primer

    $9.75

    This item cannot be shipped. Local Pickup Only

    • Color: Gray
    • Oil-based formula resists temperatures up to 2000 °F
    • For use on automotive engines and other automotive surfaces that reach intermittent temperatures up to 2000°F
    • Dries to the touch in 30 minutes, once dry, high heat must be further cured by the engines heat for increase durability
    • 12 oz. can provides coverage for up to 10 sq. ft.
    • Features an any-angle spray with a comfort tip for a professional appearance
    • Flat sheen for excellent adhesion of topcoat
    • Rust preventive for a long-lasting finish
    • Do not apply to surfaces that exceed 200°F
    • Actual paint colors may vary from on-screen and printer representations
    Quick View
  • Quick view
    Add to wishlist

    Valspar CX6431 International Harvester Red Spray Paint – 12 oz.

    $9.29

    This item cannot be shipped. Local Pickup Only

    • Available in Original Equipment Manufacturer (OEM) colors
    • Provides heavy-duty performance
    • Rust and fade resistant
    Quick View
  • Quick view
    Add to wishlist

    Walnut Shell (non-skid)

    $195.00
    Walnut Shell Grit is easily added to paint, mixed-in and applied to surfaces to create a non-skid / anti-slip coating. Walnut Shell abrasives stay in suspension in most paints, for easy mix-in applications.
    Quick View